Guide to toxins: Difference between revisions

Once you've gathered these Canisters put them onto the 3 ports directly under the tables then grab a wrench (if there isn't one around, there should be some in blue toolboxes in the R&D office at the top of the hall), then use the wrench on each Canister to connect them to the ports. Once connected there should be a black pipe going from Canister to the floor.

'''DO NOT open the Canister valves!'''  This will flood toxins immediately and you do not want that!  The Canisters will mix on their own as soon as they are wrenched in the connectors.

Once you've made sure your Canisters have the correct contents, use the wrench to disconnect the Canisters, drag one onto the port on the south-wall of Toxins. Then open the valve so the contents of the Canister are pumped from the Canister to the mixing chamber. If you changed the pump settings correctly, it's quite likely that a light bulb will smash and ignite the mix for you; if not, you can use the ignition switch on the wall of the airlock to do so.

Now once your gas is busy superheating the chamber, go down the corridor and grab one of the yellow Canisters and attach that it to the port above the previous one, this Canister will hold your final heated mix.

Give the mix a few minutes in the chamber then open the valve on the pipe leading to the port with your empty Canister attached.

While this method produces very hot gas, the gas is (mostly) [[CO2]]. In order to make a bomb you will require heated plasma, this can be achieved by pumping this gas into a tank that already contains plasma to heat it up as described below, but a larger explosion is possible if you have a hot tank of pure plasma without mixing in any CO2. Other methods are possible, have fun experimenting and try not to destroy the station too many times.

Now you've got your superheated gas. Next you'll want to go and get an Oxygen Canister from the storage and bring it back down to the Toxins Room, you'll be using this to top off Oxygen Tanks from the dispenser to your right, where the yellow Canisters were.

Now you'll want to start off by dispensing one or two Plasma Tanks, load into the white air scrubber next to the dispenser, making sure it's pressure is set to 1013 kPa, and get rid of all that plasma. Then take the Plasma Tanks to a Plasma Canister and put a small amount of plasma in the tank, setting the pressure to 50 kPa will work, but experiment with different amounts to change the size of the explosion. Once this is done go and slot them into one of your yellow Canisters, making sure that the output pressure is at 1013 kPa. This should result in a high pressure, high temperature tank of (mostly) plasma.

Now take these tanks of heated gas and attach each one to a tank transfer valve, once you've done that it's back to the dispenser.

This time get an equal amount of Oxygen Tanks from the dispenser and fill them with oxygen from the tank you got at the start of this section, again make sure the pressure is set to 1013 kPa. Now attach each to a transfer valve that already has a Plasma Tank on and you'll have a bomb, or several.

From here on you have 3 options, timers, proximity sensors and remote signaling devices. Each of these is a method of setting off your bomb, for your first bomb you should use a proximity sensor. To attach these devices to a tank transfer valve you need to use a screwdriver on them, or in the case of proximity sensors, don't, because they come pre-ready for attachment. Grab a readied device and click on a tank transfer valve to attach it, all done, you have a bomb, ready for use.

# Grab TWO Plasma Canister and ONE Oxygen Canister. Wrench them into the mixing ports, unless you fucked it up somehow '''ALL THREE''' Canisters should read 66% Plasma and 33% Oxygen (if you're not sure that it's the proper amount, enable the Gas Scanner on your [[PDA]] and check the Canisters with it).

## ''(optional)'' For a max yielding bomb, take a trip down to atmos and get a chilled Oxygen Canister from them.

# Once you got the Canisters 66% Plasma and 33% Oxygen, take one of them and wrench it into the Input Port and turn the Red Wheel. Take one of the Empty Yellow Canister and wrench it into the Output port. Once the plasma is in the mixing room, hit the ignition switch (if the Canister that you wrenched into the Input port runs dry, replace it with another Canister if you want).

# You're good to go! Turn the Red Wheel on the Output Port and fill er' Up! Keep an eye on the meter for the Output Port, wait until it reads a temperature of 97 000 degrees celsius.  

# Grab a Plasma Tank and fill it with the superheated plasma, grab an Oxygen Tank and fill it up with (chilled?) oxygen.

# Grab a Transfer Valve and slap the filled oxygen/Plasma Tank on it.

# Decide how you want your bomb to detonate (if you want to attach a signaler, proxy, or timer use the screwdriver on the device and attach it to the transfer valve).