System Operators, Wiki Staff
855
edits
Thermo-Electric Generator: Difference between revisions
Jump to navigation
Jump to search
→How to Set Up the TEG
(Updates the guide to the one written by User:Wandering Host) |
|||
| Line 3: | Line 3: | ||
[[File:TEG.png|650px|thumb]] | [[File:TEG.png|650px|thumb]] | ||
=How to Set Up the TEG= | =How to Set Up the TEG= | ||
#{{anchor|step one}}Screwdriver and wrench the circulators from the ground. | This is a basic setup that will yield estimately 600-800kW which is enough to charge most of the SMES. | ||
# | #{{anchor|step one}}Screwdriver and wrench the circulators and generator to release them from the ground. | ||
# | #At '''point 1''', move the circulators and generator to the positions shown, alt-click the circulators to rotate them to the correct orientation. | ||
#Wrench | #Wrench the circulators and generator into place. | ||
# | #Using a multitool, change the mode of the circulators to the correct mode for each side (''1 tap = cold, 2 taps = hot''). | ||
#Screwdriver shut the circulators and the generator. | |||
# | #Wrench the center generator to complete the engine assembly. | ||
# | #At '''point 2''', wrench down all of the CO2 cannisters. | ||
#At '''points 3, 4 and 5''', turn on the pumps and max them. | |||
#At '''point 6''', turn on the filter. | |||
#At '''points 7 and 8''', turn on the pumps and max them. | |||
#At '''point 9''', set the mixer to a burn mix, turn on the mixer to max pressure. ''(The nodes are coloured to determine which node is which gas, a default mix would be 40/60 oxygen/plasma, different ratios alter heat output and gas production'')''.'' (''NOTE: burn mix is tested to last nearly 50 minutes if you empty both tanks).'' | |||
#At '''point 10''', turn on the pump and max it | |||
#At '''point 11''', press the top button to close the blast doors to the burn mix chamber. | |||
#Once some gasses have entered the chamber, press the bottom button at point 11 to ignite the mix. | |||
#At '''point 12''', turn on and set the filter to filter out CO2, H2O, Tritium, and Pluoxium. | |||
#At '''point 13''', wrench down both of the CO2 canisters. | |||
#At '''points 14, 15 and 16''', turn on the pumps and max them. | |||
#Once pressure/heat builds up in the hot loop and the burn mix is over 30,000C, turn on the valves at '''points 17 and 18'''. | |||
=TEG Fundamentals= | =TEG Fundamentals= | ||
The Thermo-Electric Generator is a simple engine. This engine uses hot and cold gas, (''hot and cold sides of the circulators'') to generate energy. To make more power, you will need to scale the hot and cold gasses and maintain the temperature difference between them. The limiting factor being how the engine is set up and having too great of a difference in gas temperature. A great difference in temperature can overpower the other circulator, preventing power generation. However, an unmodified engine will usually lead you into the biggest, most common problem: clogs. | The Thermo-Electric Generator is a simple engine. This engine uses hot and cold gas, (''hot and cold sides of the circulators'') to generate energy. To make more power, you will need to scale the hot and cold gasses and maintain the temperature difference between them. The limiting factor being how the engine is set up and having too great of a difference in gas temperature. A great difference in temperature can overpower the other circulator, preventing power generation. However, an unmodified engine will usually lead you into the biggest, most common problem: clogs. | ||
| Line 33: | Line 43: | ||
*Increase coolness to the cold loop by adding more gas or expand cooling loop. | *Increase coolness to the cold loop by adding more gas or expand cooling loop. | ||
''NOTE: if these don't work then it might be needed to replace the pressure pumps with volume pumps'' | ''NOTE: if these don't work then it might be needed to replace the pressure pumps with volume pumps'' | ||
=Troubleshooting= | =Troubleshooting= | ||
<div class="toccolours mw-collapsible mw-collapsed" style="width:1000px"> | <div class="toccolours mw-collapsible mw-collapsed" style="width:1000px"> | ||
| Line 70: | Line 79: | ||
'''Answer:''' It is possible that you set the TEG's cold and hot loops on the wrong side, if true there should have been a short time of a loop indicating some flow before completey stopping, check inside the TEG's display that the cold loop is indeed cold and not hot. If the loops are the wrong way around, un-wrench the TEG apart, open both circulators with a screwdriver, and multitool both circulators, screwdriver both circulators closed then wrench it back together. | '''Answer:''' It is possible that you set the TEG's cold and hot loops on the wrong side, if true there should have been a short time of a loop indicating some flow before completey stopping, check inside the TEG's display that the cold loop is indeed cold and not hot. If the loops are the wrong way around, un-wrench the TEG apart, open both circulators with a screwdriver, and multitool both circulators, screwdriver both circulators closed then wrench it back together. | ||
</div></div> | </div></div> | ||
=Sabotaging The TEG= | =Sabotaging The TEG= | ||
Unfortunately for filthy traitors, the TEG is a safe engine, however that doesn't mean you cannot stop it from producing power. | Unfortunately for filthy traitors, the TEG is a safe engine, however that doesn't mean you cannot stop it from producing power. | ||
*Your greatest tool for sabotaging this engine is how daunting the pipe works look, something as simple as turning off the injector from the computer console or turning off the filter will cause the TEG to clog inside the loop and will reduce the power output until the hot loop is non-functional. | *Your greatest tool for sabotaging this engine is how daunting the pipe works look, something as simple as turning off the injector from the computer console or turning off the filter will cause the TEG to clog inside the loop and will reduce the power output until the hot loop is non-functional. | ||
| Line 83: | Line 90: | ||
*Simply opening the plasma canister at max pressure will start a plasma fire in the room that will destroy the TEG and the observation computer, this option should be done with care as atmos fuckery will often raise the ire of the admins. | *Simply opening the plasma canister at max pressure will start a plasma fire in the room that will destroy the TEG and the observation computer, this option should be done with care as atmos fuckery will often raise the ire of the admins. | ||
There are many other creative ways to mess around with the TEG, just take care to not violate the murder bone rules, whilst a TEG won't explode its high-end damage is station ending, more so than that of a loose tesla or singularity. | There are many other creative ways to mess around with the TEG, just take care to not violate the murder bone rules, whilst a TEG won't explode its high-end damage is station ending, more so than that of a loose tesla or singularity. | ||