Guide to mapping: Difference between revisions
Jump to navigation
Jump to search
→Shuttles
imported>Oranges m (→Shuttles) |
imported>MrStonedOne |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 49: | Line 49: | ||
== Pre-commit checks == | == Pre-commit checks == | ||
*Are floors with or without air, as they should be? (regular or airless) | |||
*Does the area have an APC? | |||
*Does the area have an Air Alarm? | |||
*Does the area have a Request Console? | |||
*Does the area have lights? | |||
*Does the area have a light switch? | |||
*Does the area have enough intercoms? | |||
*Does the area have enough security cameras? (Use the verbs under Mapping for help) | |||
*Is the area connected to the scrubbers air loop? | |||
*Is the area connected to the vent air loop? (vent pumps) | |||
*Is everything wired properly? | |||
*Does the area have a fire alarm and firedoors? | |||
*Do all pod doors work properly? | |||
*Are accesses set properly on doors, pod buttons, etc. | |||
*Are all items placed properly? (not below vents, scrubbers, tables) | |||
*Does the disposal system work properly from all the disposal units in this room and all the units, the pipes of which pass through this room? | |||
*Check for any misplaced or stacked piece of pipe (air and disposal) | |||
*Check for any misplaced or stacked piece of wire | |||
*Identify how hard it is to break into the area and where the weak points are, and balance the area accordingly (eg. the Vault should be made of reinforced structures and electrified windows, the Kitchen should not) | |||
*Check if the area has too much empty space. If so, make it smaller and replace the rest with maintenance tunnels | |||
*Are there any [[guide_to_mapping#Room Structure|unsimulated floors]] where they shouldn't be? | |||
== General Station-wide Mapping Guidelines == | == General Station-wide Mapping Guidelines == | ||
| Line 233: | Line 234: | ||
=== Access === | === Access === | ||
Access to doors is handled by req_access values. There are four when editing a door - req_access, req_access_txt, req_one_access, and req_one_access_txt. The one's we're concerned with are '''req_access_txt''' and '''req_one_access_txt'''. | |||
[[File:DoorAccessImage1.png|thumb|left|300px]] This image shows a door on the Arrivals shuttle - since it's a public door, the access is set to "0", as everyone should be able to open it. If we look at the Brig front door, we would set the access to 63, because that's the value for Security front doors - accessible by Security positions, but no one else. | |||
Multiple accesses to doors are handled by adding a semicolon (with no spaces) between access values (eg. "28;31" is for Kitchen and Cargo access). This might seem worthless, but it's useful for small maps, where jobs might need to share access due to cramped spaces. | |||
There's an important difference between the two that you need to pay attention to - req_access_txt requires '''ALL LISTED ACCESSES''' to open the door, while req_one_access_txt lets anyone with '''ONE OF THE LISTED ACCESSES''' open the door. For example - say you want your Brig to be openable by the Detective and Security Officers, we would put "63;4" in '''req_one_access_txt''', because we want the Detective '''AND''' Security to have access. If we used req_access_txt, you would need '''BOTH''' accesses to open the door, meaning neither the Detective or Security could open it. | |||
You can view all of the access values in the code/game/jobs/access.dm file. (Most should be self explanatory or have a label, but if you really aren't sure, you can take a look at Boxstation's map file and check the value on the door you're looking for). | |||
=== Airless Floors === | === Airless Floors === | ||
| Line 285: | Line 290: | ||
You need to add the dock types to the map and edit the bounding boxes via varediting the dock, you need to varedit height, width, dheight and dwidth at minimum. These are offset by the dir so do keep that in mind, eg if dir == 2 then width goes from EAST to WEST, if dir == 4 then width goes from NORTH to SOUTH and dwidth/dheight are offsets from the lower-left corner of the plane switched to the dock's dir | You need to add the dock types to the map and edit the bounding boxes via varediting the dock, you need to varedit height, width, dheight and dwidth at minimum. These are offset by the dir so do keep that in mind, eg if dir == 2 then width goes from EAST to WEST, if dir == 4 then width goes from NORTH to SOUTH and dwidth/dheight are offsets from the lower-left corner of the plane switched to the dock's dir | ||
You should also ensure the directions face the shuttle or face away from the thing the shuttle docks with. | |||
If a shuttle's mobile docking port direction is different then the stationary docking port's direction, the shuttle and all items on it will be rotated accordingly. (Try it, it works properly for just about everything) | |||
'''Warning the bounding box for the mobile dock must fit inside of the stationary dock (after any rotation)''' Or the shuttle will refuse to move. | |||
If the shuttle's mobile docking port is in an area that is a subtype of /area/shuttle, Only turfs in the bounding box in that same area are moved. Otherwise it moves all turfs in the bounding box. This can be used for odd shaped shuttles. (the area will be transfer over as well) | |||
Also note that the emergency shuttle and cargo shuttle need special subtypes of the dock type eg so /obj/docking_port/mobile/emergency | Also note that the emergency shuttle and cargo shuttle need special subtypes of the dock type eg so /obj/docking_port/mobile/emergency | ||