7
edits
Wondering host
Joined 3 August 2023
think im done with this
(some grammatical fixes and sentence alteration) |
(think im done with this) |
||
| Line 8: | Line 8: | ||
=How to Set Up the TEG= | =How to Set Up the TEG= | ||
#{{anchor|step one}}Screwdriver and wrench the circulators from the ground. | #{{anchor|step one}}Screwdriver and wrench the circulators from the ground. | ||
#Move the circulators to the squares beside the generator. Wrench down once in place ''make sure to orientate them with the notches beside the generator before wrenching | #Move the circulators to the squares beside the generator. Wrench down once in place. (''make sure to orientate them with the notches beside the generator before wrenching [alt-click to turn]).'' | ||
#Now in place we need to multi tool the circulators. Changing the mode, once done then screwdriver shut (''1 tap = cold 2 taps = hot''). | #Now in place we need to multi tool the circulators. Changing the mode, once done then screwdriver shut (''1 tap = cold 2 taps = hot''). | ||
#Wrench down the center to complete the engine. | #Wrench down the center to complete the engine assembly. | ||
#Turn on pumps and max them, open valves, press buttons if need be (''Follow the orange and cyan pipes.''). | #Turn on pumps and max them, open valves, press buttons if need be (''Follow the orange and cyan pipes.''). | ||
#Wrench down some of the CO2 canisters to the connectors and turn on pumps | #Wrench down some of the CO2 canisters to the connectors and turn on pumps. | ||
#Go to the incinerator and check if the blast doors are close. | #Go to the incinerator and check if the blast doors are close. If not, then press the buttons on the table. | ||
#Open up the air alarm and enter the scrubber menu, find the scrubber in the incinerator chamber and set range: '''Expanded'''. | #Open up the air alarm and enter the scrubber menu, find the scrubber in the incinerator chamber and set range: '''Expanded'''. | ||
#Prepare burn mix, (different ratios alter heat output and gas production), then turn on mixer to max pressure. Then turn on igniter. | #Prepare burn mix, (''different ratios alter heat output and gas production''), then turn on mixer to max pressure. Then turn on igniter. (''burn mix is tested to last nearly 50 minutes if you empty both tanks).'' | ||
=TEG Fundamentals= | =TEG Fundamentals= | ||
The Thermo-Electric Generator is a simple engine. This engine uses hot and cold gas (hot and cold sides of circulators) to generate energy. To make more power, you will need to scale the hot and cold gasses and maintain the temperature difference between them. The limiting factor being how the engine is set up and having too great of a difference in gas temperature. | The Thermo-Electric Generator is a simple engine. This engine uses hot and cold gas, (hot and cold sides of the circulators) to generate energy. To make more power, you will need to scale the hot and cold gasses and maintain the temperature difference between them. The limiting factor being how the engine is set up and having too great of a difference in gas temperature. A great difference in temperature can overpower the other circulator. However, an unmodified engine will usually lead you into the biggest problem: clogs. | ||
Clogging happens when gasses in the hot loop gets too hot for pumps to handle. Pumps (and valves) are limiters to this engine, pressure pumps clog the easiest because they pass little, precise amounts of fuel. Volume pumps fare better but will also eventually clog. Though there does exist a | Clogging happens when gasses in the hot loop gets too hot for pumps to handle. Pumps, (and valves) are limiters to this engine, pressure pumps clog the easiest because they pass little, precise amounts of fuel. Volume pumps fare better but will also eventually clog. Though there does exist a clog-less pump, the documentation for it can be found [[Thermo-Electric Generator optimizations|here]]. | ||
''NOTE: You can't have straight pipes all the way around because gas would not flow and would just stay still.'' | ''NOTE: You can't have straight pipes all the way around because gas would not flow and would just stay still.'' | ||
| Line 36: | Line 36: | ||
*Release some gas. | *Release some gas. | ||
*Increase coolness to the cold loop by adding more gas. | *Increase coolness to the cold loop by adding more gas. | ||
NOTE: if these don't work then it might be needed to replace the pressure pumps with volume pumps | ''NOTE: if these don't work then it might be needed to replace the pressure pumps with volume pumps'' | ||
==Maintaining the SMESs== | ==Maintaining the SMESs== | ||
In general, the SMESs don't need maintenance. However, there are a few times when they do need to be handled specially, namely during the following instances. | In general, the SMESs don't need maintenance. However, there are a few times when they do need to be handled specially, namely during the following instances. | ||