Wondering host

Joined 3 August 2023
110 bytes added ,  21:47, 28 August 2023
ok finally done
(think im done with this)
(ok finally done)
Line 13: Line 13:
#Turn on pumps and max them, open valves, press buttons if need be (''Follow the orange and cyan pipes.'').
#Turn on pumps and max them, open valves, press buttons if need be (''Follow the orange and cyan pipes.'').
#Wrench down some of the CO2 canisters to the connectors and turn on pumps.
#Wrench down some of the CO2 canisters to the connectors and turn on pumps.
#Go to the incinerator and check if the blast doors are close. If not, then press the buttons on the table.
#Go to the incinerator and check if the blast doors are closed. If not, then press the buttons on the table.
#Open up the air alarm and enter the scrubber menu, find the scrubber in the incinerator chamber and set range: '''Expanded'''.
#Open up the air alarm and enter the scrubber menu, find the scrubber in the incinerator chamber and set range: '''Expanded'''.
#Prepare burn mix, (''different ratios alter heat output and gas production''), then turn on mixer to max pressure. Then turn on igniter. (''burn mix is tested to last nearly 50 minutes if you empty both tanks).''
#Prepare burn mix, (''different ratios alter heat output and gas production''), then turn on mixer to max pressure. Then turn on igniter. (''NOTE: burn mix is tested to last nearly 50 minutes if you empty both tanks).''
=TEG Fundamentals=
=TEG Fundamentals=
The Thermo-Electric Generator is a simple engine. This engine uses hot and cold gas, (hot and cold sides of the circulators) to generate energy. To make more power, you will need to scale the hot and cold gasses and maintain the temperature difference between them. The limiting factor being how the engine is set up and having too great of a difference in gas temperature. A great difference in temperature can overpower the other circulator. However, an unmodified engine will usually lead you into the biggest problem: clogs.
The Thermo-Electric Generator is a simple engine. This engine uses hot and cold gas, (''hot and cold sides of the circulators'') to generate energy. To make more power, you will need to scale the hot and cold gasses and maintain the temperature difference between them. The limiting factor being how the engine is set up and having too great of a difference in gas temperature. A great difference in temperature can overpower the other circulator, preventing power generation. However, an unmodified engine will usually lead you into the biggest, most common problem: clogs.


Clogging happens when gasses in the hot loop gets too hot for pumps to handle. Pumps, (and valves) are limiters to this engine, pressure pumps clog the easiest because they pass little, precise amounts of fuel. Volume pumps fare better but will also eventually clog. Though there does exist a clog-less pump, the documentation for it can be found [[Thermo-Electric Generator optimizations|here]].
Clogging happens when gasses in the hot loop gets too hot for the pumps to handle. Pumps, (''and valves'') are limiters to this engine, pressure pumps clog the easiest because they pass little, precise amounts of gas. Volume pumps fare better but will also eventually clog. Though there does exist a clog-less pump, the documentation for it can be found [[Thermo-Electric Generator optimizations|<u>here</u>]].


''NOTE: You can't have straight pipes all the way around because gas would not flow and would just stay still.''
''NOTE: You can't have straight pipes all the way around because gas would not flow and would just stay still.''
Line 30: Line 30:
Self-explanatory. the gas in the cold loop is too cold compared to the hot loop, this can be caused by a number of things. however easily remedied by two things
Self-explanatory. the gas in the cold loop is too cold compared to the hot loop, this can be caused by a number of things. however easily remedied by two things
*release some gas or filter it back to the storage tanks.
*release some gas or filter it back to the storage tanks.
*increase heat to the hot loop by adding more gas to it.
*increase heat to the hot loop by adding more gas to it or alter fuel ratio.
'''TEMP DIFFERENCE (TOO HOT)!!'''
'''TEMP DIFFERENCE (TOO HOT)!!'''


Like above but for too hot
Like above but for too hot
*Release some gas.
*Release some gas.
*Increase coolness to the cold loop by adding more gas.
*Increase coolness to the cold loop by adding more gas or expand cooling loop.
''NOTE: if these don't work then it might be needed to replace the pressure pumps with volume pumps''
''NOTE: if these don't work then it might be needed to replace the pressure pumps with volume pumps''
==Maintaining the SMESs==
==Maintaining the SMESs==